Simulation accuracy of the unsteady flow past slender cylinders: Evaluation and improvement of under hood simulation accuracy

Visa enkel post
dc.contributor.authorWästlund, Hannes
dc.contributor.departmentChalmers tekniska högskola / Institutionen för mekanik och maritima vetenskapersv
dc.contributor.departmentChalmers University of Technology / Department of Mechanics and Maritime Sciencesen
dc.date.accessioned2019-07-03T14:51:25Z
dc.date.available2019-07-03T14:51:25Z
dc.date.issued2018
dc.description.abstractThe aim of the present study is to improve the accuracy of the predicted ow topology in the engine bays of cars when using both simple turbulence models based on the concept of Reynolds averaged Navier-Stokes (RANS) and more advanced models such as Detached Eddy Simulations (DES) and Large Eddy Simulations (LES). The focus has been to investigate the simple RANS models capability of predicting separation and the influence of unsteady wake movements (i.e vortex shedding) on the size of the created regions with recirculating flows and how much the accuracy can be improved by switching to the more advanced modelling approaches. In order to simplify the analysis of the studied models, they were tested on simple blu bodies of cylindrical shape with different cross sections. The investigated geometries included polygonal shapes with 2, 4, 7, 8 and 16 sides and a circular cross section. The geometries were tested at different orientations and at a Reynolds number of Red = 1 104, which is equivalent to that found for similar geometries in engine bays. The square cross section was also tested at a Reynolds number of Red = 2:2 104. Both of these Reynolds numbers are below the critical number, which means that the boundary layers prior to separation is laminar. The behaviour of the di erent models have been compared to both experimental results, the LES results obtained in the present study and those from other numerical studies. The investigated RANS models included k Realizable, k! SST, Reynolds Stress Model, k v02 2f and Spalart-Allmaras. An investigation of the development of the vortices and the transport of momentum into the base region predicted by eddy viscosity models, represented by k ! SST, was performed for the square cross section. It was found that the initial creation of the vortices is fundamentally different than that found in experiments and by scale resolving methods. The actual creation of the vorticies takes place in the free shear layers after the separation points where small disturbances are amplified, turned into vortices and then enlarged by roll-up. For the eddy viscosity models, which are unable to resolve the roll-up process, the creation of the vortices are instead provided by separation at the trailing corner of the geometry. The modelled development of the vortex and the accumulation of mass and momentum into the vortices seems to be connected to their shape during the initial part of their existence, during which the vortices stick to the back side of the cylinder. The behaviour was found to be the result of a low pressure zone in the inner most part of the viscous sub-layer, which creates a force toward the surface of the cylinder. Further out in the bu er layer and the log-layer the force changes sign and is directed donwstream, partially due to the turbulent di usion term. As a result an overestimation of the turbulence kinetic energy promotes the release of the vortices. The current flow contains many of the known weaknesses of the eddy viscosity approach, like a number of regions with stagnation flow and curved streamlines, which gives an overestimation of turbulent kinetic energy. The consequence is that the recirculation region lengths is underestimated by the eddy viscosity models due to increased transport of momentum into the wake. It is believed that this behaviour also in uences the Strouhal number by increasing the vortex shedding frequency. It was found that the eddy viscosity models are able to predict the vortex shedding process with an acceptable level of accuracy for polygonal shapes. However, the circular cross section constituted a bigger challenge. The recirculation region length was underestimated by approximately 30%. The separation was predicted to occur later than experiments performed by Bearman [2] and correlates with the expected separation behaviour at increased levels of turbulence. In order to get results of adequate accuracy for the separation point and recirculation region length, scale resolving approaches were needed.
dc.identifier.urihttps://hdl.handle.net/20.500.12380/255723
dc.language.isoeng
dc.relation.ispartofseriesExamensarbete - Institutionen för mekanik och maritima vetenskaper : 2018:44
dc.setspec.uppsokTechnology
dc.subjectStrömningsmekanik och akustik
dc.subjectHållbar utveckling
dc.subjectTransport
dc.subjectFluid Mechanics and Acoustics
dc.subjectSustainable Development
dc.subjectTransport
dc.titleSimulation accuracy of the unsteady flow past slender cylinders: Evaluation and improvement of under hood simulation accuracy
dc.type.degreeExamensarbete för masterexamensv
dc.type.degreeMaster Thesisen
dc.type.uppsokH
local.programmeApplied mechanics (MPAME), MSc
Ladda ner
Original bundle
Visar 1 - 1 av 1
Bild (thumbnail)
Namn:
255723.pdf
Storlek:
4.54 MB
Format:
Adobe Portable Document Format
Beskrivning:
Fulltext
Ladda ner
Samling
Examensarbeten för masterexamen